Welsh Text to Speech

2 free Welsh AI voices

SpeakScribe has two Welsh (Cymraeg) text-to-speech voices: Nia (female) and Aled (male). Welsh spelling uses digraphs such as ll, dd, ch and ff as single letters, and its consonant mutations change the start of words, so type them as written.

Nia

Female · British

GLOBAL
Use voice

Aled

Male · British

GLOBAL
Use voice

How Welsh is written, and what to type so the voice reads it right

Welsh is written with the Latin alphabet, and several pairs of letters count as single letters in the alphabet: ch, dd, ff, ll, ng, ph, rh and th. Splitting a digraph (writing c and h separately, for instance) changes the word, so keep each digraph together.

Welsh changes the first letter of a word after certain words and in some grammatical forms. These mutations are part of the spelling. The word fy (my) triggers a mutation in the word that follows it: ci (dog) becomes nghi in fy nghi (my dog), while llais (voice) keeps its ll in the sample line 'Dyma fy llais i.'

  • Keep the circumflex on ŵ and ŷ where the word has it: dŵr (water) is written with ŵ.
  • Keep the nasal mutation after fy: fy nghi (my dog), not fy ci.

Numbers, dates, abbreviations and loanwords in Welsh scripts

Welsh dates are normally written with the day number, the month name and the year, such as 22 Hydref 2026 for 22 October 2026.

Welsh has many words borrowed from English, often adapted to Welsh spelling, such as ffôn (phone) with its ô. Write the Welsh spelling where it exists, and check that a borrowed word follows the Welsh letters rather than the English ones.

  • Dates: 22 Hydref 2026 (Hydref is October).
  • Keep the Welsh spelling of borrowed words: ffôn (phone), not a copy of the English spelling.

Accents and regional varieties

Welsh has regional varieties, and the North and South of Wales differ in pronunciation and in some vocabulary. Standard written Welsh is used across all regions, in schools, broadcasting and official text.

Nia and Aled carry a British accent label and no Welsh regional variety. Standard written Welsh is the safe base for a general audience, and a regional word from one part of Wales may not be familiar to listeners from another.

Choosing between the Welsh voices

The two voices are close in pitch. Nia's median pitch is 170.8 Hz and Aled's is 179.2 Hz, so Aled is slightly higher on this measure. Nia's spectral centroid is 1619 Hz against 1690 Hz for Aled, so Aled is also slightly brighter. Pitch alone is not the difference between these two voices.

Nia has an intonation range of 13.1 semitones and Aled of 12.2, so their movement across a sentence is similar. Choose between them by the narrator you want for the video, then preview each on a longer Welsh paragraph. Both read the sample line in about two and a half to three seconds.

Common mistakes when turning Welsh text into speech

The points below are the errors that change Welsh words most often. They are simple to fix once they are seen.

  • Typing w or y for ŵ and ŷ, as in dwr for dŵr (water). The circumflex is a separate vowel letter, so switch to a Welsh layout.
  • Writing y cath (the cat) with the plain c. After the article y the soft mutation applies, so the text is y gath.
  • Adding a stress mark for pronunciation. Welsh stress normally falls on the penultimate syllable, so no mark is written or needed.
  • Copying an English word with its English spelling, such as phone, when a Welsh spelling exists. Use ffôn.

Welsh voices compared — measured

Each voice read the same Welsh text at normal speed. Lower pitch sounds deeper; a wider intonation range sounds livelier, a narrower one steadier.

VoiceGenderAccent PitchIntonation range Speaking rate
Nia GLOBAL Female British 171 Hz 13.1 st 14.3 chars/s
Aled GLOBAL Male British 179 Hz 12.2 st 15.6 chars/s

Measured by SpeakScribe in October 2026 from each voice's audio. Pitch is the median fundamental frequency; intonation range is the spread between the 10th and 90th percentile of pitch. Speaking rate is characters per second, spaces included, on the ~15-second sample passage that every Welsh voice reads. st = semitones. Methodology · How SpeakScribe voices work

Frequently asked questions

It reads the letters you type. Keep each digraph together, because ll, dd, ch and ff are single letters in Welsh, and writing them apart changes the word.
Two: Nia (female) and Aled (male).
Yes. Mutations are part of standard Welsh spelling, so write them as they occur, for example fy nghi (my dog) rather than fy ci.
Yes. Keep Welsh words in Welsh spelling and English names as typed, then preview the paragraph to check that the mix sounds right to you.
Use the Welsh form, such as Caerdydd for Cardiff, because the Welsh spelling is the form used in Welsh text and the one listeners of Welsh expect.
The library labels both voices with a British accent. Write standard written Welsh, because regional spellings and words will not always match the standard form on the page.

Generate Welsh voiceover audio free

Pick a voice above, paste your script, and export publish-ready audio in seconds.

Open Voice Studio